Connecting 2 computers

[rohan]

I have 2 computers at home. One of them is pretty old but can somehow manage to run Unreal tournament. So, what i have thought is to connect those two computers on a LAN. I have a budget of around 1.5K, including the LAN cards and the cabling. Also, I have a free PCI slot on each PC, so the card won't be a problem.

At the same time, I have two 56.6K modems [the dialup ones, which have a RJ25 connector port]. Can i use them to connect these two computers? Would it be enough for me to run Unreal Tournament in multiplayer mode. If it is, it would save me some money, and i could buy some RAM for my old computer.

I need suggestions on how to setup a network for these two computers. I would require around 20m of cabling...

 

[ravi_9793]

I have 2 computers at home. One of them is pretty old but can somehow manage to run Unreal tournament. So, what i have thought is to connect those two computers on a LAN. I have a budget of around 1.5K, including the LAN cards and the cabling. Also, I have a free PCI slot on each PC, so the card won't be a problem.

I will explain in brief:
You Need
1) LAN cable..with cross climped.
2) LAN card on both computer.

At the same time, I have two 56.
6K modems [the dialup ones, which have a RJ25 connector port]. Can i use them to connect these two computers?

I have never seen any network on RJ11 or RF25 connector.

I need suggestions on how to setup a network for these two computers. I would require around 20m of cabling...

Please search forum...there are many with your answer.

Just connect both PC...and set IP setting as:
PC1
IP-->>192.168.0.1
subnet mast-->>255.255.255.0
default gateway-->>blank

DNS-->> leave blank, if you dont want to share internet.


PC2
IP-->>192.168.0.2
subnet mast-->>255.255.255.0
default gateway-->>192.168.0.1

DNS-->> leave blank, if you dont want to share internet.

 

[Harvik780]

^^Ravi it won't work the pcs are too far.He would require a Switch.

Buy a switch(8 port rs 600).Buy two lan cards(Rs 500 total).

U need this type of wiring

|1.2.3.4| |1.2.3.4| when both heads are kept parallel the wires say 1,2,3,4 will align in this manner.
Get a 1 meter wire and a 19 meter wire(rs 375).
Connect the wires to your Lan cards.Connect the other ends of the wires to your Switch.
Configure in this manner.

LAN properties
TCP/IP properties
PC1

IP address - 192.168.0.X1 (X1 may be any number from 1 to 254)
Subnet Mask - 255.255.255.0
Default Gateway - Blank

PC2
IP address - 192.168.0.X2(X2 may be any value from 1 to 254 but not X1)
Subnet mask - 255.255.255.0
Default Gateway - 192.168.0.X1
DNS server - (Give same as Default Gateway only if u want to surf net from PC1)

 

[ravi_9793]

^^Ravi it won't work the pcs are too far.He would require a Switch.

It will work mate.
This is not a case of simple DSL modem..which don't support long wires.

 

[rohan]

It will work mate.
This is not a case of simple DSL modem..which don't support long wires.

even i think it should. It's just 20m. I have seen people cabling over around 60-70m across 2 floors in a building without a hub/switch.

 

[din]

Yes, 20m is not a problem - form my experience.

 

[Harvik780]

But it was for me that's why I bought a switch.My pcs are 20meter apart and LAN was not detected on either pcs until i connected them by a switch.

 

[ravi_9793]

But it was for me that's why I bought a switch.My pcs are 20meter apart and LAN was not detected on either pcs until i connected them by a switch.

r u sure you were using cross climped wire..with proper configuration. ??

 

[Harvik780]

Oh forgot.Actually the vendor had not clipped the wires properly.I made parallel wires so i had to use a switch.
Yes LAN to LAN cable should work without any issues.Sorry,I apologize for creating confusion.

 

[ravi_9793]

Oh forgot.Actually the vendor had not clipped the wires properly.I made parallel wires so i had to use a switch.
Yes LAN to LAN cable should work without any issues.Sorry,I apologize for creating confusion.

Never mind dear
galti to sab se hoti hain

 

[skghosh44]

I have gone through this thread and tried to connect my 2 pc, but I cant sucess. Will any one guide me the correct procedure.

Specification :

DSL UT300R2U modem 256 kbs
PC1 = Win XP Pro with 2 lan card (one onboard and other on PCI slot)
PC2 = Win XP SP-2 with one onboard lan card.
Cable = 1) 10 mts CAT5 cable with both end climped
2) 1 mtr CAT 5 cable supplied with DSL Modem
Now tell me how can I connect 2 pcs along with configuration.

 

[rohan]

Q] What the hell does a cross clip mean [or cross clipping, for that purpose]?

 

[ravi_9793]

Q] What the hell does a cross clip mean [or cross clipping, for that purpose]?

A LAN cable is combination of 8 different color wires.It is clipped in two ways.
1) straight
2) cross

I have gone through this thread and tried to connect my 2 pc, but I cant sucess. Will any one guide me the correct procedure.

Specification :

DSL UT300R2U modem 256 kbs
PC1 = Win XP Pro with 2 lan card (one onboard and other on PCI slot)
PC2 = Win XP SP-2 with one onboard lan card.
Cable = 1) 10 mts CAT5 cable with both end climped
2) 1 mtr CAT 5 cable supplied with DSL Modem
Now tell me how can I connect 2 pcs along with configuration.

how exactly you want your network??

 

[skghosh44]

Mainly file sharing/accessing between the two home pc. Net connection in the 2nd PC is secondary.