- Status
Hi Guys purchased MSI P45 NEO F for 6000 and E7200 for 5500 a week ago, This is a great combo for most of the economic(only for name sake
) enthusiasists, In past i heard a lot of problems regarding this mobo , but faced nothing in reality, it even overclocks the E7200 to 3.6 ghz , without any increase in voltage (increased only the FSB), that too with stock cooling!!!!! Go for this combo friends!!!!!!!
) enthusiasists, In past i heard a lot of problems regarding this mobo , but faced nothing in reality, it even overclocks the E7200 to 3.6 ghz , without any increase in voltage (increased only the FSB), that too with stock cooling!!!!! Go for this combo friends!!!!!!!
Last edited:
OP
comp@ddict
EXIT: DATA Junkyard
Yes, and they would have to increase he volts too, and FSB OCing isn't one of the strong points of AMD proccessors...
Hi Guys purchased MSI P45 NEO F for 6000 and E7200 for 5500 a week ago, This is a great combo for most of the economic(only for name sake
Reportedly, it can go to 4GHz!!!! with a simple volts increase, at stock cooling too. But honestly, 3.6GHz is more than enough.
Last edited:
my friend best way is to start learning it with a system ...after having read some basic tutorial and understanding DO's and DON'ts of overclocking ....and i m in same boat as u ..haven't done much overclocking myself ....but if i know something i can happily tell u ...
nish_higher
Wise Old Owl
Sorry .typo there (new keyboard hehe) .it is 45hp instead of 35hp(no such board exists ) .
@acewin-
+1 for ingame's advice. the only thing u need to take care of is temperatures and voltages..nothing else.processors and rams have a specified max voltage.if u stay below, u can fiddle with the frequencies easily.
Last edited:
OP
comp@ddict
EXIT: DATA Junkyard
Use CPU-Z as monitoring tool, and aftr OC, run a game to check stability, and keep an eye on vCore and temps, u dun wann ur procc to fry now do u
Power_user_EX
Searching for Anti-Matter
To run all stability tests use :
1) Prime95
2) Super PI
3) Intel Burn in Test ***
Use Intel Burn in test with high end coolers only - it will raise ur tCase and tJunc temps to very high levels within 30 to 40 secs.
Prime 95 is widely used and accepted sw for stability test.
1) Prime95
2) Super PI
3) Intel Burn in Test ***
Use Intel Burn in test with high end coolers only - it will raise ur tCase and tJunc temps to very high levels within 30 to 40 secs.
Prime 95 is widely used and accepted sw for stability test.
OP
comp@ddict
EXIT: DATA Junkyard
I think I've found this awesome thing. It's generally hard to find notebook gfx cards comparisions and cpu comparisions, here is it....and it came aftr long, i was tired of searching, almost given up, accidentally clicked a link and got THIS tadda.......::::
*www.notebookcheck.net/Mobile-Graphics-Cards-Benchmark-List.844.0.html
*www.notebookcheck.net/Mobile-Processors-Benchmarklist.2436.0.html
Do go through them once and tell me if this search was of any use...
*www.notebookcheck.net/Mobile-Graphics-Cards-Benchmark-List.844.0.html
*www.notebookcheck.net/Mobile-Processors-Benchmarklist.2436.0.html
Do go through them once and tell me if this search was of any use...
OP
comp@ddict
EXIT: DATA Junkyard
Look, an Overclocking Guide for Beginners too, do check::::::
*www.hexus.net/content/item.php?item=9808
*www.hexus.net/content/item.php?item=9808
darklord
Cyborg Agent
First of,
drop the HTT multiplier to 3X and then bump the HTT bus slowly. This should get you started.
Aim for 2.4GHz or so. Dont expect AMD to clock like Intel does. The IMC makes things a bit trickier
Post back what you can do once you do this and then i will tell you further.
Yo dudes My config- core2 quad q6600,8600 GT ddr3,2.48 GB ram ddr 2,intel dg33bu.
I am a complete newbie to overlocking.
Anyway whatz overlocking and how to do it.
I have heard that it voids warrenty.
I am a complete newbie to overlocking.
Anyway whatz overlocking and how to do it.
I have heard that it voids warrenty.
OP
comp@ddict
EXIT: DATA Junkyard
Yes it dows. If any damage is done(i mean reversible) just set to default and claim warranty, don't tell the idiot techie tht u Oced....
Now for the Q6600, yes, oh but noooo, DG 33 suks in OCing.
U do it from the bios, slowly increasing the FSB, inistally 5FSB shud be enough.
Try to clock at 2.8GHz, that shud be a wonder with DG33.....
And increase the Vcore(max 1.43 for you, a li'l increase shud be enough, again from the bios, but don't even by mistake exceed, or ur procc will be baked b'fore u can say OOPS!)
And don't xpect good oc cause of mobo restriction....
8600GT yes, 256mb ddr3 is nice, if ur card runs cool(rare for a 8600GT), then try riva tuner, and increase the memory and core and shader clocks one by one. Don't increase more than 30Mhz for each, however, memory is 45Mhz + go ahead....
If u do it sweetly, u'll get a 30% increase withur 8600GT and another 10% wid the procc...
Now for the Q6600, yes, oh but noooo, DG 33 suks in OCing.
U do it from the bios, slowly increasing the FSB, inistally 5FSB shud be enough.
Try to clock at 2.8GHz, that shud be a wonder with DG33.....
And increase the Vcore(max 1.43 for you, a li'l increase shud be enough, again from the bios, but don't even by mistake exceed, or ur procc will be baked b'fore u can say OOPS!)
And don't xpect good oc cause of mobo restriction....
8600GT yes, 256mb ddr3 is nice, if ur card runs cool(rare for a 8600GT), then try riva tuner, and increase the memory and core and shader clocks one by one. Don't increase more than 30Mhz for each, however, memory is 45Mhz + go ahead....
If u do it sweetly, u'll get a 30% increase withur 8600GT and another 10% wid the procc...
furious_gamer
Excessive happiness
OP
comp@ddict
EXIT: DATA Junkyard
Hehe, 14 years of pure comp knowledge!!!hehe
It's been half a year since I really really took interest, and in half a year, i've learnt A LOT LOT LOT!!!
It's been half a year since I really really took interest, and in half a year, i've learnt A LOT LOT LOT!!!
furious_gamer
Excessive happiness
Hehe, 14 years of pure comp knowledge!!!hehe
It's been half a year since I really really took interest, and in half a year, i've learnt A LOT LOT LOT!!!
But u hesitate for ur exams..huh...
Anyway bro, i just think u were atleast 18 when u first posted here...
But shocked to hear u were 14...
OP
comp@ddict
EXIT: DATA Junkyard
well, till YOUNG am I not!!lolol
I am using MSI P45 Neo mobo and an e7200 processor bro!!
Can any one tell how far a transcend ddr2 800mhz (Jet Ram) can be overclocked ??? can we increasw the voltage beyond 1.8v for it???
Last edited:
- Status