nothing happens after assembling pc

Anush

Anush

Sandy Bridge User :)
Don't give up.
Give it a try once more. Check all the headers, power connections,etc. Once again.
 
OP
N

noob

Cyborg Agent
its not near RAM slot. its next to mobo headers o_Oo
and it glows.

what else i need to check ?

above CPU is a 2x2 power slot.

here i put a 4pin connector *with 2 black and 2 yellow wires. )

do u think i m putting it in wrong way or does it fits only when plugged in in a proper way ?
 
Faun

Faun

Wahahaha~!
Staff member
Can you post the whole motherboard pic with the setup you have done.

The latch should match with the wedge on the 2x2 power slot.
 
OP
N

noob

Cyborg Agent
:( , Actually, i have now packed everything. very tired. Will try fresh tomorrow morning now.
 
saswat23

saswat23

Human Spambot
I think its the problem with power connector. Check it properly, if u have connected all the power connector of the power switch on the mobo.

This is the real problem with one who doesn't know assembling. Thats why i would suggest you to call an assembler and watch him while he assembles. Mean while you can clear all your doubts from him too. This way you too can learn how to assemble a system and can assemble a system of your own.
Plz dont mind. Its just my suggestion. I am suggesting u such coz if u connect cables in wrong slots then you may end up damaging your motherboard.
But if u r confident enough then u should still try.
 
asingh

asingh

Aspiring Novelist
I cannot see the imageshack images at home. For some reason my ISP blocks it. Try a CMOS reset with the system powered down.

Also read this, about connectors you could have plugged the PCI.Ex16 6PIN into the EPS 12V. It happens.

It seems your CPU is not getting powered up.
 
OP
N

noob

Cyborg Agent
asingh said:
I cannot see the imageshack images at home. For some reason my ISP blocks it. Try a CMOS reset with the system powered down.

Also read this, about connectors you could have plugged the PCI.Ex16 6PIN into the EPS 12V. It happens.

It seems your CPU is not getting powered up.
Click to expand...

i have plugged this in to 2x2 power slot for CPU


check image too.
*www.thinkdigit.com/forum/attachments/hardware-q/4534d1304444345-nothing-happens-after-assembling-pc-22.jpg
 
asingh

asingh

Aspiring Novelist
^^
Can you read on the cable for the 2x2 that it does NOT say PCIE on it...? I will have to see your images tomorrow from office.
 
OP
N

noob

Cyborg Agent
YES. i can confirm that PSU has cables with PCIE written on it and i am NOT using any of those.

m not using iamgeshack. uploading images on digit ONLY
 
asingh

asingh

Aspiring Novelist
Okay do this. Place the board on a non conductive surface...like a soft bed sheet or something. Then hook it all up.

Could be a short circuit. You places the board on the spacers right when you placed it in the cabinet.
 
OP
N

noob

Cyborg Agent
yes. i have used stand-off and mounted mobo on that n then have plugged in screws in the holes.
 
OP
N

noob

Cyborg Agent
As i have posted in my previous comment, i have packed everything and will try tomorrow morning.

Thanks everyone. I will post my findings in morning.

I hope it works.

@asingh : Thanks. Thats the last thing i thought of doing and will do it 1st in morning now. had a very rough day. Body needs rest.

thanks to everyone once again.
 
asingh

asingh

Aspiring Novelist
^^
End of the day if it does not work out of the cabinet and you are 100% sure it is hooked up fine. You will have to take it all back to the motherboard service center. They will check it.
 
OP
N

noob

Cyborg Agent
Lets see. Have just called a friend who know a good assembler. Will check it with him 1st or else back to PrimeABGB :(
 
You must log in or register to reply here.
Top Bottom