New Hard Disk

[ritish]

hi ,
I bought a 320 GB Seagate hard disk with USB casing.
But when I connected it with my laptop, it does not read it.
What should I do. If it needs a formatting how shall it be done, as it is not showing any drive even in DOS mode.

Please suggest.

 

[iMav]

this doesnt seem to be a problem with the hdd but rather 1 with the usb casing; try using another usb port

 

[passion_unlimitedd]

First u have to make partition of the HDD using FDISK or any other disk partition utility. After that format the partitions and then only your HDD will get detected.

For making partitions you have to connect the HDD to any Desktop PC. If you dont have access to any Desktop PC then ask your vendor to make partitions on the HDD.

 

[pushkaraj]

hi ,
I bought a 320 GB Seagate hard disk with USB casing.
But when I connected it with my laptop, it does not read it.
What should I do. If it needs a formatting how shall it be done, as it is not showing any drive even in DOS mode.

Please suggest.

Connect ur usb hard disk.
Right-click on my computer and click on manage. Now on the left hand side click on Disk management. It will show u all the disks that are connected in ur pc, including ur usb hard disk. If it is a new hard disk then you need to format and partition the hard disk. That can be done by right-clicking on the hard disk icon.

 

[reachrishikh]

Don't listen to the other 2 posters, iMav is right, there is a problem with the USB casing.

Also, did you buy the 'R-Driver III - USB 2.0 to Sata/IDE cable' with the black box? I bought one recently, and that batch seems to have an inherent problem, so you can further narrow down the issue.

 

[Angad singh]

Hey dude pushkaraj is right whenever u buy a new HD u have to format it .... just follow the instructions given by pushkaraj... ur HD will work...

 

[ritish]

But I have used it as a normal hard disk, that is directly into the PC Bus & now I want to convert it to USB hard disk. So I got it cased & now it does not detect even.
what can be done...

 

[iMav]

well u need to try the differnet usb ports as i said before try connecting it to the back usb ports of ur pc and other ports of ur laptop also chk whether the casing is wrking

 

[ritish]

Casing is ok I think as the hard disk spins and the power light also glows.

 

[Hackattack]

Sometimes the USB cable is faulty(cable break). Try with different one.

 

[ritish]

but before formatting it it detected the hard disk saying "SATA connected to IDE", but after that it said "your hardware may not work properly".
but now its not showing that even.

 

[Hackattack]

I think you should not waste any time and replace it or get ur money back.

P.S. I completed 100 posts

 

[pushkaraj]

hi ,
I bought a 320 GB Seagate hard disk with USB casing.

i assumed it was new hard disk so i told u how to format the hard disk.

Anyways, try out iMav's and Hackattack's suggestions. If that dont work, then get the casing checked from your vendor or check it yourself by connecting some other hard disk.

 

[prakashr85]

connect u r hdd to pc make partition and try if it still problem change cable or other wise change the usb converter

 

[praka123]

just experienced the same problem and later found that usb enclosure is faulty.

 

[pushkaraj]

^^ The usb enclosures are the usual culprits in most of the cases. And the worst part is that they almost always fail after the 6 month warranty gets over

 

[ritish]

What I did is when it said " Your hardware may not work properly",
I formatted and partitioned it from a pc through a direct connection (non USB). Later when I enclosed it and tried to use as a USB in laptop, no reaction is seen from the laptop.

So what could have happened. Is it for I formatted it using a PC with direct connection with partitions that it does not support the USB connection or it is because of some fault from the casing side.

Plz provide ur views.

 

[passion_unlimitedd]

What I did is when it said " Your hardware may not work properly",
I formatted and partitioned it from a pc through a direct connection (non USB). Later when I enclosed it and tried to use as a USB in laptop, no reaction is seen from the laptop.

So what could have happened. Is it for I formatted it using a PC with direct connection with partitions that it does not support the USB connection or it is because of some fault from the casing side.

Plz provide ur views.

its definitely the USB casing that is creating the problem. your HDD is fine since u have made partitions and formatted it. try changing ur casing.

 

[ritish]

Issue Solved!!!!!!
It was because of the jumper in the wrong position.
Thanks all for your views. It was definitely informative.