gary4gar
GaurishSharma.com
My system refuses to boot randomly .
here is the error
now after this, all process started by init are reporting I/O errors
eg.
Here is Bit of information about my system
I suspect this error is related to SATA driver,HDD, SATA II backwards compatibility & sata port on my system.
Here is some more information.
smartctl scan results
Output of dmesg, after rebooting.
Now no error messages are displayed & system strangely behaves normal
as if nothing happened
Please post, If anything else is Required
here is the error
Code:
[ 52.308000] ata2.00: exeception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[ 52.308000] ata2.00: cmd c8/00:08:d6:4a:89/00:00:00:00/e2 tag 0 cdb 0x0 data 4096 in
[ 92.568000] ata2.00: revalidation failed (errno=-5)
[ 137.832000] ata2.00: revalidation failed (errno=-5)
eg.
and lastly i get this message,after this there are no further messages and i am forced to reboot it via REISUB* Running local boot scripts (/etc/rc.local) [ OK ]
etc/init.rc/: 2:/etc/rc2.d/S99stop=readhead: Input/output error
Code:
Buffer I/O error on device sda2, logical block 0
Here is Bit of information about my system
I am dual booting it with Windows xp Sp2.Amd Athlon 64 3000+
MSI-k8mm-v
1 GB drr 400 RAM
Nvidia 6200 128MB Graphics
Seagate ST380815AS(just 2 months old)
Ubuntu 7.10 x86
Kernel 2.6.22-14-generic
I suspect this error is related to SATA driver,HDD, SATA II backwards compatibility & sata port on my system.
Here is some more information.
Code:
gaurish@gaurish-desktop:~$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South]
00:0a.0 Modem: PCTel Inc HSP56 MicroModem (rev 04)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6200] (rev a2)
Code:
gaurish@gaurish-desktop:~$ cat /proc/version_signature
Ubuntu 2.6.22-14.52-generic
smartctl scan results
:~$ sudo smartctl -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is *smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST380815AS
Serial Number: 6RA6TP00
Firmware Version: 3.AAD
User Capacity: 80,026,361,856 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Apr 21 22:58:26 2008 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 119 100 006 Pre-fail Always - 232852004
3 Spin_Up_Time 0x0003 099 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 443
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail Always - 14672038
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 634
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 461
187 Unknown_Attribute 0x0032 001 001 000 Old_age Always - 260
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 050 049 045 Old_age Always - 841744434
194 Temperature_Celsius 0x0022 050 051 000 Old_age Always - 50 (Lifetime Min/Max 0/18)
195 Hardware_ECC_Recovered 0x001a 081 069 000 Old_age Always - 128192585
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 276 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 276 occurred at disk power-on lifetime: 339 hours (14 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 24 0d 60 e0 Error: UNC at LBA = 0x00600d24 = 6294820
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 1f 0d 60 e0 00 00:25:54.949 READ DMA EXT
25 03 01 00 00 00 e0 00 00:25:54.948 READ DMA EXT
24 03 01 af f8 50 e0 00 00:25:54.947 READ SECTOR(S) EXT
c6 03 10 af f8 50 a0 00 00:25:54.946 SET MULTIPLE MODE
91 03 3f af f8 50 af 00 00:25:54.936 INITIALIZE DEVICE PARAMETERS [OBS-6]
Error 275 occurred at disk power-on lifetime: 339 hours (14 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 24 0d 60 e0 Error: UNC at LBA = 0x00600d24 = 6294820
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 1f 0d 60 e0 00 00:25:46.872 READ DMA EXT
25 03 01 00 00 00 e0 00 00:25:46.871 READ DMA EXT
25 03 01 00 00 00 e0 00 00:25:46.870 READ DMA EXT
25 03 01 00 00 00 e0 00 00:25:46.860 READ DMA EXT
24 03 01 af f8 50 e0 00 00:25:46.857 READ SECTOR(S) EXT
Error 274 occurred at disk power-on lifetime: 339 hours (14 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 24 0d 60 e0 Error: UNC at LBA = 0x00600d24 = 6294820
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 20 1f 0d 60 e0 00 00:25:39.713 READ DMA EXT
25 03 08 17 0d 60 e0 00 00:25:39.713 READ DMA EXT
25 03 08 77 ff 9b e0 00 00:25:39.712 READ DMA EXT
25 03 08 87 ff 9b e0 00 00:25:39.712 READ DMA EXT
25 03 08 97 0f b0 e0 00 00:25:39.712 READ DMA EXT
Error 273 occurred at disk power-on lifetime: 339 hours (14 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 24 0d 60 e0 Error: UNC at LBA = 0x00600d24 = 6294820
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 80 0f 0d 60 e0 00 00:25:33.053 READ DMA EXT
24 03 01 af f8 50 e0 00 00:25:33.040 READ SECTOR(S) EXT
c6 03 10 af f8 50 a0 00 00:25:33.037 SET MULTIPLE MODE
91 03 3f af f8 50 af 00 00:25:33.027 INITIALIZE DEVICE PARAMETERS [OBS-6]
ef 03 0c af f8 50 a0 00 00:25:32.995 SET FEATURES [Set transfer mode]
Error 272 occurred at disk power-on lifetime: 339 hours (14 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 24 0d 60 e0 Error: UNC at LBA = 0x00600d24 = 6294820
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 80 0f 0d 60 e0 00 00:25:26.876 READ DMA EXT
24 03 01 af f8 50 e0 00 00:25:26.792 READ SECTOR(S) EXT
c6 03 10 af f8 50 a0 00 00:25:20.816 SET MULTIPLE MODE
91 03 3f af f8 50 af 00 00:25:20.816 INITIALIZE DEVICE PARAMETERS [OBS-6]
ef 03 0c af f8 50 a0 00 00:25:20.806 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 3 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
gaurish@gaurish-desktop:~$
Output of dmesg, after rebooting.
Now no error messages are displayed & system strangely behaves normal
as if nothing happened
Code:
[ 0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Feb 12 07:42:25 UTC 2008 (Ubuntu 2.6.22-14.52-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f4b80
[ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262128
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262128
[ 0.000000] On node 0 totalpages: 262128
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32497 pages, LIFO batch:7
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F6B80 checksum 0
[ 0.000000] ACPI: RSDP 000F6B80, 0014 (r0 VIAK8M)
[ 0.000000] ACPI: RSDT 3FFF3040, 002C (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 3FFF30C0, 0074 (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 3FFF3180, 4D34 (r1 VIAK8M AWRDACPI 1000 MSFT 100000E)
[ 0.000000] ACPI: FACS 3FFF0000, 0040
[ 0.000000] ACPI: APIC 3FFF7F00, 005A (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:12 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[ 0.000000] Built 1 zonelists. Total pages: 260081
[ 0.000000] Kernel command line: root=UUID=445bad1a-9af1-4eac-8637-9cfd3b8dcb3d ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1999.806 MHz processor.
[ 18.884038] Console: colour VGA+ 80x25
[ 18.884512] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 18.884953] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 18.906700] Memory: 1027880k/1048512k available (2015k kernel code, 19928k reserved, 915k data, 364k init, 131008k highmem)
[ 18.906710] virtual kernel memory layout:
[ 18.906711] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 18.906713] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 18.906714] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 18.906715] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 18.906716] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 18.906717] .data : 0xc02f7e86 - 0xc03dce84 ( 915 kB)
[ 18.906719] .text : 0xc0100000 - 0xc02f7e86 (2015 kB)
[ 18.906722] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 18.906759] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 18.986784] Calibrating delay using timer specific routine.. 4004.27 BogoMIPS (lpj=8008550)
[ 18.986813] Security Framework v1.0.0 initialized
[ 18.986822] SELinux: Disabled at boot.
[ 18.986834] Mount-cache hash table entries: 512
[ 18.986965] CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
[ 18.986973] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 18.986976] CPU: L2 Cache: 512K (64 bytes/line)
[ 18.986978] CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000410 00000000 00000000 00000000
[ 18.986989] Compat vDSO mapped to ffffe000.
[ 18.987001] Checking 'hlt' instruction... OK.
[ 19.002922] SMP alternatives: switching to UP code
[ 19.003129] Freeing SMP alternatives: 11k freed
[ 19.003399] Early unpacking initramfs... done
[ 19.294738] ACPI: Core revision 20070126
[ 19.294816] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 19.297315] CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 00
[ 19.297337] Total of 1 processors activated (4004.27 BogoMIPS).
[ 19.297840] ENABLING IO-APIC IRQs
[ 19.298160] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
[ 19.442801] Brought up 1 CPUs
[ 19.442926] Booting paravirtualized kernel on bare hardware
[ 19.443012] Time: 22:35:57 Date: 03/21/108
[ 19.443032] NET: Registered protocol family 16
[ 19.443104] EISA bus registered
[ 19.443121] ACPI: bus type pci registered
[ 19.450686] PCI: PCI BIOS revision 2.10 entry at 0xfb4b0, last bus=1
[ 19.450688] PCI: Using configuration type 1
[ 19.450690] Setting up standard PCI resources
[ 19.455611] ACPI: EC: Look up EC in DSDT
[ 19.459740] ACPI: Interpreter enabled
[ 19.459746] ACPI: (supports S0 S1 S4 S5)
[ 19.459762] ACPI: Using IOAPIC for interrupt routing
[ 19.464834] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 19.464845] PCI: Probing PCI hardware (bus 00)
[ 19.465615] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 19.503994] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
[ 19.504128] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
[ 19.504261] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 *12)
[ 19.504380] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 19.504496] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 19.504607] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 19.504717] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 19.504828] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[ 19.504966] ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
[ 19.505093] ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
[ 19.505220] ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
[ 19.505366] ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
[ 19.505430] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 19.505441] pnp: PnP ACPI init
[ 19.505448] ACPI: bus type pnp registered
[ 19.508537] pnp: PnP ACPI: found 13 devices
[ 19.508539] ACPI: ACPI bus type pnp unregistered
[ 19.508542] PnPBIOS: Disabled by ACPI PNP
[ 19.508584] PCI: Using ACPI for IRQ routing
[ 19.508587] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 19.532951] NET: Registered protocol family 8
[ 19.532953] NET: Registered protocol family 20
[ 19.533002] pnp: 00:00: iomem range 0xd0000-0xd3fff has been reserved
[ 19.533005] pnp: 00:00: iomem range 0xdcc00-0xdffff has been reserved
[ 19.533008] pnp: 00:00: iomem range 0xf0000-0xfbfff could not be reserved
[ 19.533010] pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
[ 19.533015] pnp: 00:02: ioport range 0x4000-0x407f has been reserved
[ 19.533018] pnp: 00:02: ioport range 0x5000-0x500f has been reserved
[ 19.534768] Time: tsc clocksource has been installed.
[ 19.563244] PCI: Bridge: 0000:00:01.0
[ 19.563246] IO window: disabled.
[ 19.563250] MEM window: f8000000-faffffff
[ 19.563253] PREFETCH window: e0000000-efffffff
[ 19.563266] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.563277] NET: Registered protocol family 2
[ 19.602811] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 19.602945] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 19.604517] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 19.605082] TCP: Hash tables configured (established 131072 bind 65536)
[ 19.605085] TCP reno registered
[ 19.614892] checking if image is initramfs... it is
[ 20.066758] Switched to high resolution mode on CPU 0
[ 20.184300] Freeing initrd memory: 7060k freed
[ 20.184643] audit: initializing netlink socket (disabled)
[ 20.184657] audit(1208817357.024:1): initialized
[ 20.184716] highmem bounce pool size: 64 pages
[ 20.186091] VFS: Disk quotas dquot_6.5.1
[ 20.186130] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 20.186216] io scheduler noop registered
[ 20.186218] io scheduler anticipatory registered
[ 20.186219] io scheduler deadline registered
[ 20.186233] io scheduler cfq registered (default)
[ 20.186246] PCI: VIA PCI bridge detected. Disabling DAC.
[ 20.186310] Boot video device is 0000:01:00.0
[ 20.186430] isapnp: Scanning for PnP cards...
[ 20.540476] isapnp: No Plug & Play device found
[ 20.558377] Real Time Clock Driver v1.12ac
[ 20.558458] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 20.558547] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.558690] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 20.559094] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.559273] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 20.559393] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 20.559587] 0000:00:0a.0: ttyS2 at I/O 0xe008 (irq = 16) is a 16450
[ 20.559710] 0000:00:0a.0: ttyS3 at I/O 0xe010 (irq = 16) is a 8250
[ 20.559763] Couldn't register serial port 0000:00:0a.0: -28
[ 20.560193] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 20.560339] input: Macintosh mouse button emulation as /class/input/input0
[ 20.560393] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 20.560395] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 20.810673] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 20.810777] mice: PS/2 mouse device common for all mice
[ 20.810867] EISA: Probing bus 0 at eisa.0
[ 20.810886] Cannot allocate resource for EISA slot 4
[ 20.810888] Cannot allocate resource for EISA slot 5
[ 20.810901] EISA: Detected 0 cards.
[ 20.810985] TCP cubic registered
[ 20.810995] NET: Registered protocol family 1
[ 20.811014] Using IPI No-Shortcut mode
[ 20.811165] Magic number: 4:928:603
[ 20.811224] hash matches device ptyd7
[ 20.811233] hash matches device ptyaa
[ 20.811586] Freeing unused kernel memory: 364k freed
[ 20.892052] input: AT Translated Set 2 keyboard as /class/input/input1
[ 22.020832] AppArmor: AppArmor initialized<5>audit(1208817358.524:2): type=1505 info="AppArmor initialized" pid=1202
[ 22.027029] fuse init (API version 7.8)
[ 22.031607] Failure registering capabilities with primary security module.
[ 22.620948] SCSI subsystem initialized
[ 22.624855] libata version 2.21 loaded.
[ 22.625887] sata_via 0000:00:0f.0: version 2.2
[ 22.626121] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 22.626130] ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
[ 22.626180] sata_via 0000:00:0f.0: routed to hard irq line 11
[ 22.626251] scsi0 : sata_via
[ 22.626298] scsi1 : sata_via
[ 22.626320] ata1: SATA max UDMA/133 cmd 0x0001e100 ctl 0x0001e202 bmdma 0x0001e500 irq 17
[ 22.626324] ata2: SATA max UDMA/133 cmd 0x0001e300 ctl 0x0001e402 bmdma 0x0001e508 irq 17
[ 22.651758] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 22.651764] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 22.690263] usbcore: registered new interface driver usbfs
[ 22.690314] usbcore: registered new interface driver hub
[ 22.690331] usbcore: registered new device driver usb
[ 22.719965] USB Universal Host Controller Interface driver v3.0
[ 22.741633] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 22.741638] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 22.830296] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 22.897751] Floppy drive(s): fd0 is 1.44M
[ 22.918597] FDC 0 is a post-1991 82077
[ 23.042234] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 23.272598] ata2.00: ATA-7: ST380815AS, 3.AAD, max UDMA/133
[ 23.272601] ata2.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 23.339218] ata2.00: configured for UDMA/133
[ 23.339322] scsi 1:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
[ 23.339726] VP_IDE: IDE controller at PCI slot 0000:00:0f.1
[ 23.339745] ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
[ 23.339756] VP_IDE: chipset revision 6
[ 23.339757] VP_IDE: not 100% native mode: will probe irqs later
[ 23.339767] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[ 23.339775] ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:pio, hdb:pio
[ 23.339786] ide1: BM-DMA at 0xe708-0xe70f, BIOS settings: hdc:DMA, hdd:pio
[ 23.339792] Probing IDE interface ide0...
[ 23.356113] sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 23.356125] sd 1:0:0:0: [sda] Write Protect is off
[ 23.356128] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 23.356140] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 23.356185] sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 23.356191] sd 1:0:0:0: [sda] Write Protect is off
[ 23.356193] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 23.356204] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 23.356208] sda: sda1 sda2 sda3
[ 23.387658] sd 1:0:0:0: [sda] Attached SCSI disk
[ 23.391782] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 23.668747] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 23.668752] EXT3-fs: write access will be enabled during recovery.
[ 23.681831] kjournald starting. Commit interval 5 seconds
[ 23.681837] EXT3-fs: recovery complete.
[ 23.681973] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.906101] Probing IDE interface ide1...
[ 24.770055] hdc: BENQ DVD DD DW1650, ATAPI CD/DVD-ROM drive
[ 25.107205] ide1 at 0x170-0x177,0x376 on irq 15
[ 25.109593] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[ 25.109601] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
[ 25.109612] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 25.109799] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 25.109826] uhci_hcd 0000:00:10.0: irq 18, io base 0x0000e800
[ 25.109951] usb usb1: configuration #1 chosen from 1 choice
[ 25.109975] hub 1-0:1.0: USB hub found
[ 25.109982] hub 1-0:1.0: 2 ports detected
[ 25.213984] ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
[ 25.213993] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 25.214010] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 25.214028] uhci_hcd 0000:00:10.1: irq 18, io base 0x0000e900
[ 25.214106] usb usb2: configuration #1 chosen from 1 choice
[ 25.214125] hub 2-0:1.0: USB hub found
[ 25.214131] hub 2-0:1.0: 2 ports detected
[ 25.317981] ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
[ 25.317991] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 25.318012] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 25.318033] uhci_hcd 0000:00:10.2: irq 18, io base 0x0000ea00
[ 25.318116] usb usb3: configuration #1 chosen from 1 choice
[ 25.318136] hub 3-0:1.0: USB hub found
[ 25.318144] hub 3-0:1.0: 2 ports detected
[ 25.421925] ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
[ 25.421932] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 25.421947] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 25.421965] uhci_hcd 0000:00:10.3: irq 18, io base 0x0000eb00
[ 25.422042] usb usb4: configuration #1 chosen from 1 choice
[ 25.422061] hub 4-0:1.0: USB hub found
[ 25.422068] hub 4-0:1.0: 2 ports detected
[ 25.526064] ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
[ 25.526075] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 25.526093] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 25.526131] ehci_hcd 0000:00:10.4: irq 18, io mem 0xfb001000
[ 25.526137] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.526204] usb usb5: configuration #1 chosen from 1 choice
[ 25.526223] hub 5-0:1.0: USB hub found
[ 25.526230] hub 5-0:1.0: 8 ports detected
[ 25.630213] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[ 25.630221] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 19
[ 25.630306] eth0: VIA Rhine II at 0x1ed00, 00:11:09:06:18:c6, IRQ 19.
[ 25.631020] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
[ 26.817650] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 26.994645] usb 2-2: configuration #1 chosen from 1 choice
[ 28.602085] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 30.035265] Linux agpgart interface v0.102 (c) Dave Jones
[ 30.074983] agpgart: Detected AGP bridge 0
[ 30.078904] agpgart: AGP aperture is 128M @ 0xf0000000
[ 30.194500] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 30.294394] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 30.901302] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 30.901310] Uniform CD-ROM driver Revision: 3.20
[ 31.500839] nvidia: module license 'NVIDIA' taints kernel.
[ 31.755664] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 31.755880] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
[ 31.776862] input: PC Speaker as /class/input/input2
[ 31.791886] parport_pc 00:0b: reported by Plug and Play ACPI
[ 31.791938] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 31.809946] usbcore: registered new interface driver hiddev
[ 31.822426] input: Microsoft Basic Optical Mouse as /class/input/input3
[ 31.822473] input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:10.1-2
[ 31.822487] usbcore: registered new interface driver usbhid
[ 31.822490] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 32.327174] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 32.327183] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 21
[ 32.327320] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 33.426746] lp0: using parport0 (interrupt-driven).
[ 33.465292] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (version 2.00.00)
[ 33.465330] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x2
[ 33.465332] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x6
[ 33.465335] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
[ 33.530884] w83627hf: Found W83627THF chip at 0x290
[ 33.532323] w83627hf w83627hf.656: Reading VID from GPIO5
[ 33.904174] EXT3 FS on sda2, internal journal
[ 34.816100] kjournald starting. Commit interval 5 seconds
[ 34.816253] EXT3 FS on sda3, internal journal
[ 34.816258] EXT3-fs: mounted filesystem with ordered data mode.
[ 35.901926] input: Power Button (FF) as /class/input/input4
[ 35.906141] ACPI: Power Button (FF) [PWRF]
[ 35.939259] input: Power Button (CM) as /class/input/input5
[ 35.943440] ACPI: Power Button (CM) [PWRB]
[ 36.019085] No dock devices found.
[ 36.963138] Failure registering capabilities with primary security module.
[ 37.215828] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 37.215833] apm: overridden by ACPI.
[ 19.512000] Marking TSC unstable due to: cpufreq changes.
[ 19.516000] Time: acpi_pm clocksource has been installed.
[ 20.440000] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 20.440000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 20.440000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 21.556000] ppdev: user-space parallel port driver
[ 21.796000] audit(1208797578.220:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4924 profile="/usr/sbin/cupsd"
[ 23.552000] Clocksource tsc unstable (delta = -142799059 ns)
Please post, If anything else is Required
Last edited: