mario_pant
In the zone
hey does anyone know about any caller ID software... which runs on the modem???
- Status
pallavnawani
Broken In
*www.analogx.com
Look for their caller ID software (free).
Pallav
Look for their caller ID software (free).
Pallav
OP
mario_pant
In the zone
umm.. any other?? and hey... it says something about a voice enabled modem??? whats that!
vijaythefool
In the zone
its not going to work unless u have a caller id capable modem.
there are many softwares like
Ascendis called id
Talking caller id .......
there are many softwares like
Ascendis called id
Talking caller id .......
nikhilpoddar
Broken In
Hi,
How to know whether my modem supports caller id facility or not?????
How to know whether my modem supports caller id facility or not?????
vijaythefool
In the zone
The first is required as only your local telephone company can supply this data. The second is required so that the data sent by the telephone company can be passed to software programs for processing.
Many current MODEMs offer support for Caller ID. The key question is always what setup string to use to enable Caller ID (virtually every MODEM disables Caller ID as the default).
For most MODEMs, the string AT#CID=1 or AT+VCID=1will enable Caller ID. Look in the user’s manual for your MODEM to see if any setup string is referenced or mentioned.
Other common setup strings are:
AT#CID=2
AT%CCID=1
AT%CCID=2
AT#CC1
AT*ID1
The best way to test is to use a terminal data program. In Windows 3.X, the TERMINAL program (usually in the accessories folder) can be used, (be sure you set the COM port to the PORT your MODEM uses). In Windows 95/98/ME/2000/XP, the HyperTerminal program can be used.
To use HyperTerminal do the following:
1) Select "HyperTerminal" by navigating through the Start button to "Programs," then "Accessories," then "HyperTerminal"
2) Double click on "hyperterm" or "hyperterm.exe"
3) Name the new connection "test," and select OK
4) Change the "connect using" to Direct to COM X, were X is the COM port used by the Caller ID device
5) Click on OK on the screen for port settings
To test your MODEM, do the following:
1. Type the string ATZ, (OK should appear on the screen)
2. Enter the Caller ID string to be tested, (AT#CID=1 or AT+VCID=1 for most modems)
3. If OK results, continue; If ERROR results the modem may not support Caller ID; try a different setup string
4. Have someone call you and watch the terminal screen
5. If Caller ID is working, you will see the word RING, followed by one or more additional data lines. The word RING will then continue to appear for each incoming ring.
6. If Caller ID is not working, you will only see the word RING for each incoming ring. If this is the case try another setup string and go back to step 2.
The most common result, when Caller ID data works, is the following:
RING
DATE = xxxxx
TIME = xxxx
NMBR = xxxxxxxxx
NAME = xxxxxxxx
RING
RING …
There are other formats as well. The key point is that other data generally appears between the first and second rings.
Many current MODEMs offer support for Caller ID. The key question is always what setup string to use to enable Caller ID (virtually every MODEM disables Caller ID as the default).
For most MODEMs, the string AT#CID=1 or AT+VCID=1will enable Caller ID. Look in the user’s manual for your MODEM to see if any setup string is referenced or mentioned.
Other common setup strings are:
AT#CID=2
AT%CCID=1
AT%CCID=2
AT#CC1
AT*ID1
The best way to test is to use a terminal data program. In Windows 3.X, the TERMINAL program (usually in the accessories folder) can be used, (be sure you set the COM port to the PORT your MODEM uses). In Windows 95/98/ME/2000/XP, the HyperTerminal program can be used.
To use HyperTerminal do the following:
1) Select "HyperTerminal" by navigating through the Start button to "Programs," then "Accessories," then "HyperTerminal"
2) Double click on "hyperterm" or "hyperterm.exe"
3) Name the new connection "test," and select OK
4) Change the "connect using" to Direct to COM X, were X is the COM port used by the Caller ID device
5) Click on OK on the screen for port settings
To test your MODEM, do the following:
1. Type the string ATZ, (OK should appear on the screen)
2. Enter the Caller ID string to be tested, (AT#CID=1 or AT+VCID=1 for most modems)
3. If OK results, continue; If ERROR results the modem may not support Caller ID; try a different setup string
4. Have someone call you and watch the terminal screen
5. If Caller ID is working, you will see the word RING, followed by one or more additional data lines. The word RING will then continue to appear for each incoming ring.
6. If Caller ID is not working, you will only see the word RING for each incoming ring. If this is the case try another setup string and go back to step 2.
The most common result, when Caller ID data works, is the following:
RING
DATE = xxxxx
TIME = xxxx
NMBR = xxxxxxxxx
NAME = xxxxxxxx
RING
RING …
There are other formats as well. The key point is that other data generally appears between the first and second rings.
vijaythefool
In the zone
As far as i know u need not perform al those tests.
i dont think there are any caller id supported brand of modem.
if u are trying ith ur dlink modem , then it will disappoint u , cos no internal dial up modem come with caller id facilility. i just confirmet with d-link
i dont think there are any caller id supported brand of modem.
if u are trying ith ur dlink modem , then it will disappoint u , cos no internal dial up modem come with caller id facilility. i just confirmet with d-link
- Status