kaustav_geek
1337 |)00|) \m/
Akshay, which distro were you on ? I'd say you stick to FC 6 or 7 coz me and my friend have had it easiest to set up such an internet connection in it.
sudo wvdial BT
please help my bluetooth dongle works fine on XP it uses a software Bluesoeil in XP .X Error: BadDevice, invalid or uninitialized input device 169
Major opcode: 147
Minor opcode: 3
Resource id: 0x0
Failed to open device
X Error: BadDevice, invalid or uninitialized input device 169
Major opcode: 147
Minor opcode: 3
Resource id: 0x0
Failed to open device
Session management error: Authentication Rejected, reason : None of the authentication protocols specified are supported and host-based authentication failed
$ lsusb
$ /sbin/lsusb
[pathik@localhost ~]$ wvdialconf /etc/wvdial.conf
Scanning your serial ports for a modem.
ttyS0<Info>: Device or resource busy Port Scan<*1>: S0
ttyS1<Info>: Device or resource busy Port Scan<*1>: S1
ttyS2<Info>: Device or resource busy Port Scan<*1>: S2
ttyS3<Info>: Device or resource busy Port Scan<*1>: S3
ttyACM0<Info>: Device or resource busy Port Scan<*1>: ACM0 Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at *open.nit.ca/wvdial/ If you still have problems, send mail to wvdial-list@lists.nit.ca. [pathik@localhost ~]$ wvdial --> WvDial: Internet dialer version 1.54.0 --> Cannot open /dev/ttyACM0: Device or resource busy --> Cannot open /dev/ttyACM0: Device or resource busy --> Cannot open /dev/ttyACM0: Device or resource busy [pathik@localhost ~]$
[pathik@localhost ~]$ su
Password:
[root@localhost pathik]# wvdialconf /etc/wvdial.conf
Scanning your serial ports for a modem.
WvModem<*1>: Cannot get information for serial port.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud,
next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud,
next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<Info>: No such device or address Port Scan<*1>: S1
ttyS2<Info>: No such device or address Port Scan<*1>: S2
ttyS3<Info>: No such device or address Port Scan<*1>: S3
WvModem<*1>: Cannot get information for serial port.
ttyACM0<*1>: ATQ0 V1 E1 -- OK ttyACM0<*1>: ATQ0 V1 E1 Z -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyACM0<*1>: Modem Identifier: ATI -- Nokia
ttyACM0<*1>: Speed 4800: AT -- OK
ttyACM0<*1>: Speed 9600: AT -- OK
ttyACM0<*1>: Speed 19200: AT -- OK
ttyACM0<*1>: Speed 38400: AT -- OK
ttyACM0<*1>: Speed 57600: AT -- OK
ttyACM0<*1>: Speed 115200: AT -- OK
ttyACM0<*1>: Speed 230400: AT -- OK
ttyACM0<*1>: Speed 460800: AT -- OK
ttyACM0<*1>: Max speed is 460800; that should be safe.
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found an USB modem on /dev/ttyACM0. Modem configuration written to /etc/wvdial.conf. ttyACM0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
[root@localhost pathik]# kwrite /etc/wvdial.conf
Session management error: Authentication Rejected, reason : None of the authentication protocols specified are supported and host-based authentication failed Session management error: Authentication Rejected, reason : None of the authentication protocols specified are supported and host-based authentication failed kbuildsycoca running...
ScimInputContextPlugin()
~ScimInputContextPlugin()
ScimInputContextPlugin()
~ScimInputContextPlugin()
[root@localhost pathik]# wvdial
--> WvDial: Internet dialer version 1.54.0
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ ATZ OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK
--> Modem initialized.
--> Sending: ATDT*99#
--> Waiting for carrier.
ATDT*99# CONNECT ~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> Carrier detected. Waiting for prompt. ~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> PPP negotiation detected.
--> Starting pppd at Wed Jul 18 01:15:35 2007
--> pid of pppd: 4187
--> Using interface ppp0
--> local IP address 10.190.132.131
--> remote IP address 10.6.6.6
--> primary DNS address 202.56.230.5
--> secondary DNS address 202.56.240.5
ICE default IO error handler doing an exit(), pid = 4404, errno = 0
~ScimInputContextPlugin()
harshiloh said:how to asure my bluetooth hardware is installed,(iam using fedora7,lap with inbuilt bluetooth).
$ lsusb | grep Blue
$ lspci | grep Blue
What preferences are you talking about????how to change my bluetooth prefrence in fedora7
$ sudo wvdialconf /etc/wvdial.conf