sumonpathak
knocking on heavens door
Introduction
Asus has adopted the policy of releasing a board for every form factor or niche since the release of Z87 chipset by Intel We have
Close look of the Maximus VII Formula
*techarx.com/wp-content/uploads/2015/02/4LdwVipyTF7r3dyY_setting_fff_1_90_end_1000.png
Before going into the benchmarks lets take a tour of the Maximus VII Formula,We have given a "naked" picture of the board to accustom our readers with the board components which in case of the Formula are covered with a thermal armor.
*techarx.com/wp-content/uploads/2015/02/P_20150227_163845-768x1024.jpg
Even without the ROG Armor the board looks absolutely stunning
Now let's start a visual tour of the board.
*techarx.com/wp-content/uploads/2015/02/P_20150227_163906-1024x768.jpg
The top left hand corner of the motherboard has a 4-pin fan header, and 8-pin+4-pin CPU power connectors. Starting from the middle we have the Memok! button which helps in the booting up the system with any type of DDR3 memory.Besides that we have the ever helpful Q Code LED which displays a code in case of a system failure;between the memok! button and QCode led we have the voltage measure points useful on testing the board and in case of sub zero overclocking. A closer look at the probe points are given below
*techarx.com/wp-content/uploads/2015/02/P_20150227_170158-1024x768.jpg
*techarx.com/wp-content/uploads/2015/02/P_20150227_164044-768x1024.jpg
Just under the LED panel we see the Big Start and reset buttons which has become a trademark of ROG series,. The main attraction of the left side are however the four Ram slots supporting upto 32GB of Memory,memory speeds are supported upto 3300 Mhz(OC).ASUS’ T-Topology design is used here meaning that the trace paths to the CPU and therefore memory controller are equal. Beside the ram slots we see two power phases dedicated to the memory subsytem only.To round of this section we see the main ATX 24Pin power connector and the front USB 3.0 connectors. The power connectors hides the device leds which offers a quick reference guide in case the system fails to boot.
*techarx.com/wp-content/uploads/2015/02/P_20150227_165105-1024x768.jpg
Coming further down we have the storage section and the Z97 Chipset hub
*techarx.com/wp-content/uploads/2015/02/P_20150227_164107-768x1024.jpg
There are 8 SATA 6Gb/s ports and 2 SATA Express ports. These are controlled by the Intel Z97 Express chipset, an ASMedia ASM1061 controller and an ASMedia 106SE controller for SATA Express support which alternatively provides two additional SATA 6Gb/s ports if SATA Express slot is not populated.
*techarx.com/wp-content/uploads/2015/02/P_20150227_164539-1024x768.jpg
Coming further down the we see the Nuvoton I/O controller chip along the TPU chip.
*techarx.com/wp-content/uploads/2015/02/lower_right_end.png
The section also consists of the onboard KeyBot button,front panel connectors,Front USB2.0 connectors and ROG extender connectors(for hooking up a ROG Front Base) along with a fan header.
*techarx.com/wp-content/uploads/2015/02/lower_left_end-1024x300.jpg
Coming to the lower left side we can find a fan header,a TPM(Trusted Platform Module) header,A TB header(thunderbolt),and lastly the AAFP connector commonly known as the Front Panel Audio Connector(don't ask me why it was named as such!)
*techarx.com/wp-content/uploads/2015/03/P_20150227_165314-1024x768.jpg
Next up in the left side we have Supreme FX Audio solution which in essence an ALC1150 with ASUS secret sauce. The features included
*techarx.com/wp-content/uploads/2015/02/P_20150227_163845_edited-768x1024.png
*techarx.com/wp-content/uploads/2015/02/P_20150227_164008-1024x768.jpg
On the graphics side of things the board has 3 PCIe Slots with the top two running in both PCIe 3.0/2.0 mode and the bottom one running at only PCIe 2.0 mode. All the slots run at full x16 speeds when individually populated. The board supports Three way CrossfireX at x8/x8/x4 speed and Quad SLI(Two Dual GPU cards) at x8/x8 speed since there isn't any PLX chip onboard. Do note The PCIe 2.0 x16 slot shares bandwidth with SATAExpress_E1 (bottom one)connector. The default setting is in Auto mode that automatically optimizes the system bandwidth. If you install PCIe 2.0 x4 device, the system will automatically detect and disable SATAExpress_E1 connector. There are 3 PCIe 2.0 x1 slots for peripherals such as sound cards etc.
*techarx.com/wp-content/uploads/2015/02/P_20150227_164845-1024x768.jpg
On the VRM side of things Asus used its hugely successful DIGI+ design which is in its third revision by now. The revision scream "overkill" and what we have here is really overkill;we have a 8+2 phase design for the CPU,NB and Dram. The full implementation consists of special black metallic Nichicon GT series caps are up to 10,000 hours at 105C operating temperatures along with gold plated “Blackwing” units which have a very unique look with a fin design running vertically on the outer shell of the choke allowing for even better thermal capabilities and ensuring minimal power loss and maximum power delivery.To round it off we have special mofset which is upto 50% smaller(according to Asus) ensuring 90% more efficiency(again as said by Asus). Running the whole implementation is the Digi+ controller which provides different modes of power delivery as the the situation warrants form optimized mode to full power mode. That concludes the board layout,let us move on the Bios and software bundles which at times can make or break the board
Maximus VII Formula BIOS
As earlier i will let the pictures do the talking mostly.
Extreme Tweaker
This is where you should be if you are interested in overclocking. I will do a proper Bios guide if I get more chance but for now pictures will suffice since they are pretty much self explanatory
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_1.jpg
Extreme Tweaker 1
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_2.jpg
Extreme Tweaker 2
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_3.jpg
Extreme Tweaker 3
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_4.jpg
Extreme Tweaker 4
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_5.jpg
Extreme Tweaker 5
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_5.jpg
Extreme Tweaker 5
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_dram.jpg
Extreme Tweaker Dram Timing Control
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_gpu.jpg
Extreme Tweaker GPU/DIMM Post Info
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_digi-.jpg
Extreme Tweaker Digi+
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_tp.jpg
Tweakers Paradise
*techarx.com/wp-content/uploads/2015/03/150206221430.jpg
CPU Power Management 1
*techarx.com/wp-content/uploads/2015/03/150206221445.jpg
CPU Power Management 2
*techarx.com/wp-content/uploads/2015/03/150206221454.jpg
CPU Power Management 3
Bios Main Screen
*techarx.com/wp-content/uploads/2015/03/150206221501.jpg
Bios Main
Advanced Menu
*techarx.com/wp-content/uploads/2015/03/150206221505.jpg
Advanced Main
*techarx.com/wp-content/uploads/2015/03/150206221519.jpg
CPU Settings
*techarx.com/wp-content/uploads/2015/03/150206221527.jpg
PCH Configuration
*techarx.com/wp-content/uploads/2015/03/150206221538.jpg
PSH Storage Configuration
*techarx.com/wp-content/uploads/2015/03/150206221548.jpg
System Agent Configuration
*techarx.com/wp-content/uploads/2015/03/150206221553.jpg
USB Configuration
*techarx.com/wp-content/uploads/2015/03/150206221558.jpg
Platform Misc Configuration
*techarx.com/wp-content/uploads/2015/03/150206221611.jpg
On-board Device Configuration 1
*techarx.com/wp-content/uploads/2015/03/150206221622.jpg
On-board Device Configuration 2
*techarx.com/wp-content/uploads/2015/03/150206221627.jpg
APM Configuration
*techarx.com/wp-content/uploads/2015/03/150206221632.jpg
Network Stack Configuration
*techarx.com/wp-content/uploads/2015/03/150206221639.jpg
ROG Led Effect
Monitor Menu
*techarx.com/wp-content/uploads/2015/03/150206221645.jpg
Monitor 1
*techarx.com/wp-content/uploads/2015/03/150206221651.jpg
Monitor 3
*techarx.com/wp-content/uploads/2015/03/150206221811.jpg
Monitor 3
*techarx.com/wp-content/uploads/2015/03/150206221823.jpg
Monitor 4
Boot Menu
*techarx.com/wp-content/uploads/2015/03/150206221828.jpg
Boot 1
*techarx.com/wp-content/uploads/2015/03/150206221833.jpg
Boot 2
Tools Menu
*techarx.com/wp-content/uploads/2015/03/150206221843.jpg
Tools 1
*techarx.com/wp-content/uploads/2015/03/150206221912.jpg
Tools 2
Exit Menu
*techarx.com/wp-content/uploads/2015/03/150206221920.jpg
and that concludes the Bios portion.
Test setup and Benchmarks
First lets give you an overview of the full overview of our test rig for this review.
4000MHz
*valid.canardpc.com/cache/banner/9n3p1f-4.png
4100MHz
*valid.canardpc.com/cache/banner/buvzvz-4.png
4300MHz
*valid.canardpc.com/cache/banner/4h2lj4-4.png
4500MHz
*valid.canardpc.com/cache/banner/qksxlq-4.png
With that aside lets dive into benchmark numbers. First in our list is one of the most non biased Synthetic benchmarks i have seen : Aida 64 Part one of the CPU suite consists of the Queen and PhotoWorxx Benchmark. a brief description of the benchmarks will help the readers to understand more
CPU Queen Benchmark
This simple integer benchmark focuses on the branch prediction capabilities and the misprediction penalties of the CPU. It finds the solutions for the classic "Queens problem" on a 10 by 10 sized chessboard. At the same clock speed theoretically the processor with the shorter pipeline and smaller misprediction penalties will attain higher benchmark scores. For example -- with HyperThreading disabled -- the Intel Northwood core processors get higher scores than the Intel Prescott core based ones due to the 20-step vs 31-step long pipeline. CPU Queen test uses integer MMX, SSE2 and SSSE3 optimizations.
CPU PhotoWorxx Benchmark
This benchmark performs different common tasks used during digital photo processing. It performs the following tasks on a very large RGB image:
*techarx.com/wp-content/uploads/2015/03/aida_cpu_1.jpg
Part two of the CPU Suite consists of Hash,Zlib and AES benchmarks.
CPU ZLib Benchmark
This integer benchmark measures combined CPU and memory subsystem performance through the public ZLib compression library. CPU ZLib test uses only the basic x86 instructions, and it is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
CPU AES Benchmark
This benchmark measures CPU performance using AES (Advanced Encryption Standard) data encryption. In cryptography AES is a symmetric-key encryption standard. AES is used in several compression tools today, like 7z, RAR, WinZip, and also in disk encryption solutions like BitLocker, FileVault (Mac OS X), TrueCrypt. CPU AES test uses the appropriate x86, MMX and SSE4.1 instructions, and it's hardware accelerated on VIA PadLock Security Engine capable VIA C3, VIA C7, VIA Nano and VIA QuadCore processors; and on Intel AES-NI instruction set extension capable processors. The test is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
CPU Hash Benchmark
This benchmark measures CPU performance using the SHA1 hashing algorithm defined in the Federal Information Processing Standards Publication 180-4. The code behind this benchmark method is written in Assembly, and it is optimized for every popular AMD, Intel and VIA processor core variants by utilizing the appropriate MMX, MMX+/SSE, SSE2, SSSE3, AVX, AVX2, XOP, BMI, and BMI2 instruction set extension. CPU Hash benchmark is hardware accelerated on VIA PadLock Security Engine capable VIA C7, VIA Nano and VIA QuadCore processors.
*techarx.com/wp-content/uploads/2015/03/aida_cpu_2.jpg
Now coming to the benchmarks which stresses the FPU, we have
FPU VP8 Benchmark
This benchmark measures video compression performance using the Google VP8 (WebM) video codec Version 1.1.0 (*www.webmproject.org). FPU VP8 test encodes 1280x720 pixel ("HD ready") resolution video frames in 1-pass mode at 8192 kbps bitrate with best quality settings. The content of the frames are generated by the FPU Julia fractal module. The code behind this benchmark method utilizes the appropriate MMX, SSE2, SSSE3 or SSE4.1 instruction set extension, and it is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
FPU Julia Benchmark
This benchmark measures the single precision (also known as 32-bit) floating-point performance through the computation of several frames of the popular "Julia" fractal. The code behind this benchmark method is written in Assembly, and it is extremely optimized for every popular AMD, Intel and VIA processor core variants by utilizing the appropriate x87, 3DNow!, 3DNow!+, SSE, AVX, AVX2, FMA, and FMA4 instruction set extension. FPU Julia test is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
*techarx.com/wp-content/uploads/2015/03/aida_fpu_1.jpg
Coming to the second part of FPU benchmarks we have,
FPU Mandel Benchmark
This benchmark measures the double precision (also known as 64-bit) floating-point performance through the computation of several frames of the popular "Mandelbrot" fractal. The code behind this benchmark method is written in Assembly, and it is extremely optimized for every popular AMD, Intel and VIA processor core variants by utilizing the appropriate x87, SSE2, AVX, AVX2, FMA, and FMA4 instruction set extension. FPU Mandel test is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
FPU SinJulia Benchmark
This benchmark measures the extended precision (also known as 80-bit) floating-point performance through the computation of a single frame of a modified "Julia" fractal. The code behind this benchmark method is written in Assembly, and it is extremely optimized for every popular AMD, Intel and VIA processor core variants by utilizing trigonometric and exponential x87 instructions. FPU SinJulia is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
*techarx.com/wp-content/uploads/2015/03/aida_fpu_2.jpg
With the mainstream synthetic benchmarks out of the way,lets try some benchmarks that is used in competitive benchmarking. Enter Super PI and WPrime
Super PI is a single threaded benchmark that calculates pi to a specific number of digits. It uses the Gauss-Legendre algorithm and is a Windows port of a program used by Yasumasa Kanada in 1995 to compute pi to 232 digits.
*techarx.com/wp-content/uploads/2015/03/superpi_1M.jpg *techarx.com/wp-content/uploads/2015/03/superpi_32m.jpg
WPrime wPrime uses a recursive call of Newton's method for estimating functions, with f(x)=x2-k, where k is the number we're sqrting, until Sgn(f(x)/f'(x)) does not equal that of the previous iteration, starting with an estimation of k/2. It then uses an iterative calling of the estimation method a set amount of times to increase the accuracy of the results. It then confirms that n(k)2=k to ensure the calculation was correct. It repeats this for all numbers from 1 to the requested maximum.
*techarx.com/wp-content/uploads/2015/03/wprime_32m.jpg *techarx.com/wp-content/uploads/2015/03/wprime_1024m.jpg
CINEBENCH is a real-world cross platform test suite that evaluates your computer's performance capabilities. CINEBENCH is based on MAXON's award-winning animation software CINEMA 4D.
*techarx.com/wp-content/uploads/2015/03/cinebench_115.jpg *techarx.com/wp-content/uploads/2015/03/cinebench_15.jpg
X264 FHD benchmark encodes a full HD (1080p) video into a high quality x264 video. This is especially CPU intensive and prefers more cores.
*techarx.com/wp-content/uploads/2015/03/x264.jpg
3DPM benchmark is made by Ian J Cutress of Anandtech. In his own words The algorithms in 3DPM employ both uniform random number generation or normal distribution random number generation, and vary in various amounts of trigonometric operations, conditional statements, generation and rejection, fused operations, etc. The benchmark runs through six algorithms for a specified number of particles and steps, and calculates the speed of each algorithm, then sums them all for a final score. This is an example of a real world situation that a computational scientist may find themselves in, rather than a pure synthetic benchmark. The benchmark is also parallel between particles simulated, and we test the single thread performance as well as the multi-threaded performance.
*techarx.com/wp-content/uploads/2015/03/3dpm_st.jpg *techarx.com/wp-content/uploads/2015/03/3dpm_mt.jpg
That concludes the benchmarks.Overall every score are in line as expected from a a board like Maximus VII Formula. However the 3DPM multithreaded results are kinda confusing even after multiple re runs.
Conclusion
Asus Maximus VII Formula is indeed a good board. From SupremeFX sound solution to DIGI+ VRM implementation and LN2 mode for overclockers,the board starts with a plan of catering to every niche and it executes the plan with utmost precision.Throughout our testing we found the board to be a dream to work on and easy to operate. The only downer is that the MPCIE combo is not compatible with 80mm full sized M.2 SSD. The problem is only magnified by the fact since the 60mm or the 40mm SSD 's are not available in good number yet. I would be nitpicking, but at times ASUS' exhaustive UEFI is pretty intimidating. However the overall experience remains pleasing as ever. This is ASUS' best Z97 board, but getting the best does come at a price.
Buying link :Flipkart
Asus has adopted the policy of releasing a board for every form factor or niche since the release of Z87 chipset by Intel We have
- Impact for Mini ITX
- Gene for Micro ATX
- Ranger for Entry level Full ATX with most of the essential features of ROG lineup without breaking the bank.
- Hero for those people who don't want or can afford a Formula but do not want to miss up most of the features of the Formula.
- Formula for those people who don't want to to break any overclocking record but wants to have the full ROG Experience.
- And last we have the Extreme for the one who wants to overclock to squeeze the last ounce of performance form his computer.
| Size | ATX |
| CPU Interface | LGA 1150 |
| Chipset | Intel Z97 |
| Memory slots | 4 DIMMS upto 32GB 1333MHz - 3300 MHz(OC) |
| Video Outputs | HDMI DisplayPort 1.2 |
| Network Connectivity | Intel® I218V |
| Onboard Audio | ROG SupremeFX Formula 2014 |
| Expansion Slots | 2 x PCIe 3.0/2.0 x16 (x16 or dual x8) 1 x PCIe 2.0 x16 (x4 mode) 3 x PCIe 2.0 x1, 1 x mini-PCIe 2.0 x1 |
| Onboard Storage | Intel® Z97 chipset : 1 x SATA Express port, compatible with 2 x SATA 6.0 Gb/s ports |1 x M.2 Socket 3, , with M Key, type 2260 storage devices support (both SATA & PCIE mode) 4 x SATA 6Gb/s port(s), red Support Raid 0, 1, 5, 10 Supports Intel® Smart Response Technology, Intel® Rapid Start Technology, Intel® Smart Connect Technology *3 ASMedia® SATA Express conTRoller : *4 1 x SATA Express port, compatible with 2 x SATA 6.0 Gb/s ports ASMedia® ASM1061 conTRoller : *4 2 x SATA 6Gb/s port(s), red with M key, type 2242/2260/2280 storage devices support (both SATA & PCIE mode) |
| USB 3.0 | 6 x via PCH 2 x via Asmedia ConTRoller |
| Onboard | 1 x USB 3.0 connector(s) support(s) additional 2 USB 3.0 port(s) 2 x USB 2.0 connector(s) support(s) additional 4 USB 2.0 port(s) 2 x SATA Express connector: red, with M key, type 2242/2260/2280 storage devices support (both SATA & PCIE mode) 1 x TPM header 6 x SATA 6Gb/s connector(s) 1 x Thunderbolt header(s) 1 x Front panel audio connector(s) (AAFP) 1 x System panel(s) (Q-Connector) 1 x MemOK! button(s) 10 x ProbeIt Measurement Points 1 x Thermal sensor connector(s) 1 x Power-on button(s) 1 x Reset button(s) 1 x mPCIe Combo III connector(s) 1 x ROG extension (ROG_EXT) header(s) 1 x KeyBot Button 1 x Sonic SoundStage Button |
| Power Connectors | 1 x 24-pin EATX Power connector(s) 1 x 8-pin ATX 12V Power connector(s) 1 x 4-pin ATX 12V Power connector(s) |
| Fan Headers | 1 x CPU Fan connector(s) (1 x 4 -pin) 1 x CPU OPT Fan connector(s) (1 x 4 -pin) 6 x Chassis Fan connector(s) (6 x 4 -pin) |
| IO Panel | 1 x PS/2 keyboard/mouse combo port(s) 1 x DisplayPort 1 x HDMI 1 x LAN (RJ45) port(s) 6 x USB 3.0 (blue) 2 x USB 2.0 (one port can be switched to ROG Connect) 1 x Optical S/PDIF out 6 x Audio jack(s) 1 x Clear CMOS button(s) 1 x ROG Connect On/ Off switch(es) |
| Warranty | 3 Years |
| Product Page | Link |
Close look of the Maximus VII Formula
*techarx.com/wp-content/uploads/2015/02/4LdwVipyTF7r3dyY_setting_fff_1_90_end_1000.png
Before going into the benchmarks lets take a tour of the Maximus VII Formula,We have given a "naked" picture of the board to accustom our readers with the board components which in case of the Formula are covered with a thermal armor.
*techarx.com/wp-content/uploads/2015/02/P_20150227_163845-768x1024.jpg
Even without the ROG Armor the board looks absolutely stunning
Now let's start a visual tour of the board.
*techarx.com/wp-content/uploads/2015/02/P_20150227_163906-1024x768.jpg
The top left hand corner of the motherboard has a 4-pin fan header, and 8-pin+4-pin CPU power connectors. Starting from the middle we have the Memok! button which helps in the booting up the system with any type of DDR3 memory.Besides that we have the ever helpful Q Code LED which displays a code in case of a system failure;between the memok! button and QCode led we have the voltage measure points useful on testing the board and in case of sub zero overclocking. A closer look at the probe points are given below
*techarx.com/wp-content/uploads/2015/02/P_20150227_170158-1024x768.jpg
*techarx.com/wp-content/uploads/2015/02/P_20150227_164044-768x1024.jpg
Just under the LED panel we see the Big Start and reset buttons which has become a trademark of ROG series,. The main attraction of the left side are however the four Ram slots supporting upto 32GB of Memory,memory speeds are supported upto 3300 Mhz(OC).ASUS’ T-Topology design is used here meaning that the trace paths to the CPU and therefore memory controller are equal. Beside the ram slots we see two power phases dedicated to the memory subsytem only.To round of this section we see the main ATX 24Pin power connector and the front USB 3.0 connectors. The power connectors hides the device leds which offers a quick reference guide in case the system fails to boot.
*techarx.com/wp-content/uploads/2015/02/P_20150227_165105-1024x768.jpg
Coming further down we have the storage section and the Z97 Chipset hub
*techarx.com/wp-content/uploads/2015/02/P_20150227_164107-768x1024.jpg
There are 8 SATA 6Gb/s ports and 2 SATA Express ports. These are controlled by the Intel Z97 Express chipset, an ASMedia ASM1061 controller and an ASMedia 106SE controller for SATA Express support which alternatively provides two additional SATA 6Gb/s ports if SATA Express slot is not populated.
*techarx.com/wp-content/uploads/2015/02/P_20150227_164539-1024x768.jpg
Coming further down the we see the Nuvoton I/O controller chip along the TPU chip.
*techarx.com/wp-content/uploads/2015/02/lower_right_end.png
The section also consists of the onboard KeyBot button,front panel connectors,Front USB2.0 connectors and ROG extender connectors(for hooking up a ROG Front Base) along with a fan header.
*techarx.com/wp-content/uploads/2015/02/lower_left_end-1024x300.jpg
Coming to the lower left side we can find a fan header,a TPM(Trusted Platform Module) header,A TB header(thunderbolt),and lastly the AAFP connector commonly known as the Front Panel Audio Connector(don't ask me why it was named as such!)
*techarx.com/wp-content/uploads/2015/03/P_20150227_165314-1024x768.jpg
Next up in the left side we have Supreme FX Audio solution which in essence an ALC1150 with ASUS secret sauce. The features included
- Physical PCB isolation for minimal interference
- Stainless Steel EMI protection .
- ELNA premium Japan-made audio capacitors
- Cirrus Logic® CS4398 DAC with 120dB signal-to-noise ratio
- Sonic SenseAmp : a ROG invention that detects headphone impedance and adjusts the built-in amp automatically without needing to do any hardware amplifier exchanging, designed for pitch-perfect listeners.
- Sonic SoundStage
*techarx.com/wp-content/uploads/2015/02/P_20150227_163845_edited-768x1024.png
*techarx.com/wp-content/uploads/2015/02/P_20150227_164008-1024x768.jpg
On the graphics side of things the board has 3 PCIe Slots with the top two running in both PCIe 3.0/2.0 mode and the bottom one running at only PCIe 2.0 mode. All the slots run at full x16 speeds when individually populated. The board supports Three way CrossfireX at x8/x8/x4 speed and Quad SLI(Two Dual GPU cards) at x8/x8 speed since there isn't any PLX chip onboard. Do note The PCIe 2.0 x16 slot shares bandwidth with SATAExpress_E1 (bottom one)connector. The default setting is in Auto mode that automatically optimizes the system bandwidth. If you install PCIe 2.0 x4 device, the system will automatically detect and disable SATAExpress_E1 connector. There are 3 PCIe 2.0 x1 slots for peripherals such as sound cards etc.
*techarx.com/wp-content/uploads/2015/02/P_20150227_164845-1024x768.jpg
On the VRM side of things Asus used its hugely successful DIGI+ design which is in its third revision by now. The revision scream "overkill" and what we have here is really overkill;we have a 8+2 phase design for the CPU,NB and Dram. The full implementation consists of special black metallic Nichicon GT series caps are up to 10,000 hours at 105C operating temperatures along with gold plated “Blackwing” units which have a very unique look with a fin design running vertically on the outer shell of the choke allowing for even better thermal capabilities and ensuring minimal power loss and maximum power delivery.To round it off we have special mofset which is upto 50% smaller(according to Asus) ensuring 90% more efficiency(again as said by Asus). Running the whole implementation is the Digi+ controller which provides different modes of power delivery as the the situation warrants form optimized mode to full power mode. That concludes the board layout,let us move on the Bios and software bundles which at times can make or break the board
Maximus VII Formula BIOS
As earlier i will let the pictures do the talking mostly.
Extreme Tweaker
This is where you should be if you are interested in overclocking. I will do a proper Bios guide if I get more chance but for now pictures will suffice since they are pretty much self explanatory
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_1.jpg
Extreme Tweaker 1
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_2.jpg
Extreme Tweaker 2
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_3.jpg
Extreme Tweaker 3
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_4.jpg
Extreme Tweaker 4
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_5.jpg
Extreme Tweaker 5
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_5.jpg
Extreme Tweaker 5
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_dram.jpg
Extreme Tweaker Dram Timing Control
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_gpu.jpg
Extreme Tweaker GPU/DIMM Post Info
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_digi-.jpg
Extreme Tweaker Digi+
*techarx.com/wp-content/uploads/2015/03/extreme_tweaker_tp.jpg
Tweakers Paradise
*techarx.com/wp-content/uploads/2015/03/150206221430.jpg
CPU Power Management 1
*techarx.com/wp-content/uploads/2015/03/150206221445.jpg
CPU Power Management 2
*techarx.com/wp-content/uploads/2015/03/150206221454.jpg
CPU Power Management 3
Bios Main Screen
*techarx.com/wp-content/uploads/2015/03/150206221501.jpg
Bios Main
Advanced Menu
*techarx.com/wp-content/uploads/2015/03/150206221505.jpg
Advanced Main
*techarx.com/wp-content/uploads/2015/03/150206221519.jpg
CPU Settings
*techarx.com/wp-content/uploads/2015/03/150206221527.jpg
PCH Configuration
*techarx.com/wp-content/uploads/2015/03/150206221538.jpg
PSH Storage Configuration
*techarx.com/wp-content/uploads/2015/03/150206221548.jpg
System Agent Configuration
*techarx.com/wp-content/uploads/2015/03/150206221553.jpg
USB Configuration
*techarx.com/wp-content/uploads/2015/03/150206221558.jpg
Platform Misc Configuration
*techarx.com/wp-content/uploads/2015/03/150206221611.jpg
On-board Device Configuration 1
*techarx.com/wp-content/uploads/2015/03/150206221622.jpg
On-board Device Configuration 2
*techarx.com/wp-content/uploads/2015/03/150206221627.jpg
APM Configuration
*techarx.com/wp-content/uploads/2015/03/150206221632.jpg
Network Stack Configuration
*techarx.com/wp-content/uploads/2015/03/150206221639.jpg
ROG Led Effect
Monitor Menu
*techarx.com/wp-content/uploads/2015/03/150206221645.jpg
Monitor 1
*techarx.com/wp-content/uploads/2015/03/150206221651.jpg
Monitor 3
*techarx.com/wp-content/uploads/2015/03/150206221811.jpg
Monitor 3
*techarx.com/wp-content/uploads/2015/03/150206221823.jpg
Monitor 4
Boot Menu
*techarx.com/wp-content/uploads/2015/03/150206221828.jpg
Boot 1
*techarx.com/wp-content/uploads/2015/03/150206221833.jpg
Boot 2
Tools Menu
*techarx.com/wp-content/uploads/2015/03/150206221843.jpg
Tools 1
*techarx.com/wp-content/uploads/2015/03/150206221912.jpg
Tools 2
Exit Menu
*techarx.com/wp-content/uploads/2015/03/150206221920.jpg
and that concludes the Bios portion.
Test setup and Benchmarks
First lets give you an overview of the full overview of our test rig for this review.
- CPU : Intel Core i7 4790K ES
- Motherboard : Maximus VII Formula
- Ram: GSkill Trident X 2400MHX CL10(running XMP)
- SSD: Corsair Nova 2
- Cooler: Antec Kuhler 1250
- PSU: CM V1000
4000MHz
*valid.canardpc.com/cache/banner/9n3p1f-4.png
4100MHz
*valid.canardpc.com/cache/banner/buvzvz-4.png
4300MHz
*valid.canardpc.com/cache/banner/4h2lj4-4.png
4500MHz
*valid.canardpc.com/cache/banner/qksxlq-4.png
With that aside lets dive into benchmark numbers. First in our list is one of the most non biased Synthetic benchmarks i have seen : Aida 64 Part one of the CPU suite consists of the Queen and PhotoWorxx Benchmark. a brief description of the benchmarks will help the readers to understand more
CPU Queen Benchmark
This simple integer benchmark focuses on the branch prediction capabilities and the misprediction penalties of the CPU. It finds the solutions for the classic "Queens problem" on a 10 by 10 sized chessboard. At the same clock speed theoretically the processor with the shorter pipeline and smaller misprediction penalties will attain higher benchmark scores. For example -- with HyperThreading disabled -- the Intel Northwood core processors get higher scores than the Intel Prescott core based ones due to the 20-step vs 31-step long pipeline. CPU Queen test uses integer MMX, SSE2 and SSSE3 optimizations.
CPU PhotoWorxx Benchmark
This benchmark performs different common tasks used during digital photo processing. It performs the following tasks on a very large RGB image:
- Fill the image with random colored pixels
- Rotate 90 degrees CCW
- Rotate 180 degrees
- Difference
- Color space conversion (used e.g. during JPEG conversion)
*techarx.com/wp-content/uploads/2015/03/aida_cpu_1.jpg
Part two of the CPU Suite consists of Hash,Zlib and AES benchmarks.
CPU ZLib Benchmark
This integer benchmark measures combined CPU and memory subsystem performance through the public ZLib compression library. CPU ZLib test uses only the basic x86 instructions, and it is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
CPU AES Benchmark
This benchmark measures CPU performance using AES (Advanced Encryption Standard) data encryption. In cryptography AES is a symmetric-key encryption standard. AES is used in several compression tools today, like 7z, RAR, WinZip, and also in disk encryption solutions like BitLocker, FileVault (Mac OS X), TrueCrypt. CPU AES test uses the appropriate x86, MMX and SSE4.1 instructions, and it's hardware accelerated on VIA PadLock Security Engine capable VIA C3, VIA C7, VIA Nano and VIA QuadCore processors; and on Intel AES-NI instruction set extension capable processors. The test is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
CPU Hash Benchmark
This benchmark measures CPU performance using the SHA1 hashing algorithm defined in the Federal Information Processing Standards Publication 180-4. The code behind this benchmark method is written in Assembly, and it is optimized for every popular AMD, Intel and VIA processor core variants by utilizing the appropriate MMX, MMX+/SSE, SSE2, SSSE3, AVX, AVX2, XOP, BMI, and BMI2 instruction set extension. CPU Hash benchmark is hardware accelerated on VIA PadLock Security Engine capable VIA C7, VIA Nano and VIA QuadCore processors.
*techarx.com/wp-content/uploads/2015/03/aida_cpu_2.jpg
Now coming to the benchmarks which stresses the FPU, we have
FPU VP8 Benchmark
This benchmark measures video compression performance using the Google VP8 (WebM) video codec Version 1.1.0 (*www.webmproject.org). FPU VP8 test encodes 1280x720 pixel ("HD ready") resolution video frames in 1-pass mode at 8192 kbps bitrate with best quality settings. The content of the frames are generated by the FPU Julia fractal module. The code behind this benchmark method utilizes the appropriate MMX, SSE2, SSSE3 or SSE4.1 instruction set extension, and it is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
FPU Julia Benchmark
This benchmark measures the single precision (also known as 32-bit) floating-point performance through the computation of several frames of the popular "Julia" fractal. The code behind this benchmark method is written in Assembly, and it is extremely optimized for every popular AMD, Intel and VIA processor core variants by utilizing the appropriate x87, 3DNow!, 3DNow!+, SSE, AVX, AVX2, FMA, and FMA4 instruction set extension. FPU Julia test is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
*techarx.com/wp-content/uploads/2015/03/aida_fpu_1.jpg
Coming to the second part of FPU benchmarks we have,
FPU Mandel Benchmark
This benchmark measures the double precision (also known as 64-bit) floating-point performance through the computation of several frames of the popular "Mandelbrot" fractal. The code behind this benchmark method is written in Assembly, and it is extremely optimized for every popular AMD, Intel and VIA processor core variants by utilizing the appropriate x87, SSE2, AVX, AVX2, FMA, and FMA4 instruction set extension. FPU Mandel test is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
FPU SinJulia Benchmark
This benchmark measures the extended precision (also known as 80-bit) floating-point performance through the computation of a single frame of a modified "Julia" fractal. The code behind this benchmark method is written in Assembly, and it is extremely optimized for every popular AMD, Intel and VIA processor core variants by utilizing trigonometric and exponential x87 instructions. FPU SinJulia is HyperThreading, multi-processor (SMP) and multi-core (CMP) aware.
*techarx.com/wp-content/uploads/2015/03/aida_fpu_2.jpg
With the mainstream synthetic benchmarks out of the way,lets try some benchmarks that is used in competitive benchmarking. Enter Super PI and WPrime
Super PI is a single threaded benchmark that calculates pi to a specific number of digits. It uses the Gauss-Legendre algorithm and is a Windows port of a program used by Yasumasa Kanada in 1995 to compute pi to 232 digits.
*techarx.com/wp-content/uploads/2015/03/superpi_1M.jpg *techarx.com/wp-content/uploads/2015/03/superpi_32m.jpg
WPrime wPrime uses a recursive call of Newton's method for estimating functions, with f(x)=x2-k, where k is the number we're sqrting, until Sgn(f(x)/f'(x)) does not equal that of the previous iteration, starting with an estimation of k/2. It then uses an iterative calling of the estimation method a set amount of times to increase the accuracy of the results. It then confirms that n(k)2=k to ensure the calculation was correct. It repeats this for all numbers from 1 to the requested maximum.
*techarx.com/wp-content/uploads/2015/03/wprime_32m.jpg *techarx.com/wp-content/uploads/2015/03/wprime_1024m.jpg
CINEBENCH is a real-world cross platform test suite that evaluates your computer's performance capabilities. CINEBENCH is based on MAXON's award-winning animation software CINEMA 4D.
*techarx.com/wp-content/uploads/2015/03/cinebench_115.jpg *techarx.com/wp-content/uploads/2015/03/cinebench_15.jpg
X264 FHD benchmark encodes a full HD (1080p) video into a high quality x264 video. This is especially CPU intensive and prefers more cores.
*techarx.com/wp-content/uploads/2015/03/x264.jpg
3DPM benchmark is made by Ian J Cutress of Anandtech. In his own words The algorithms in 3DPM employ both uniform random number generation or normal distribution random number generation, and vary in various amounts of trigonometric operations, conditional statements, generation and rejection, fused operations, etc. The benchmark runs through six algorithms for a specified number of particles and steps, and calculates the speed of each algorithm, then sums them all for a final score. This is an example of a real world situation that a computational scientist may find themselves in, rather than a pure synthetic benchmark. The benchmark is also parallel between particles simulated, and we test the single thread performance as well as the multi-threaded performance.
*techarx.com/wp-content/uploads/2015/03/3dpm_st.jpg *techarx.com/wp-content/uploads/2015/03/3dpm_mt.jpg
That concludes the benchmarks.Overall every score are in line as expected from a a board like Maximus VII Formula. However the 3DPM multithreaded results are kinda confusing even after multiple re runs.
Conclusion
Asus Maximus VII Formula is indeed a good board. From SupremeFX sound solution to DIGI+ VRM implementation and LN2 mode for overclockers,the board starts with a plan of catering to every niche and it executes the plan with utmost precision.Throughout our testing we found the board to be a dream to work on and easy to operate. The only downer is that the MPCIE combo is not compatible with 80mm full sized M.2 SSD. The problem is only magnified by the fact since the 60mm or the 40mm SSD 's are not available in good number yet. I would be nitpicking, but at times ASUS' exhaustive UEFI is pretty intimidating. However the overall experience remains pleasing as ever. This is ASUS' best Z97 board, but getting the best does come at a price.
Buying link :Flipkart
